Washer repair
Does your washer make strange noises and vibrates ( Most likely – Unbalanced load of laundry, The washer feet may not be locked in and contacting the floor)? Water is leaking? (Most likely – Hoses are not attached/inserted properly, Hose washers are worn, Drains are clogged), won’t drain or spin correctly (Most likely – Drainage problems are most commonly caused by clogged hoses, improper loading of clothes, obstructions or too much detergent.). Appliance repair will help you! Our technicians specialize in all major brands of Washers, such as Amana, Asko, Bosch, LG, Samsung, Sub Zero, GE Hotpoint and many more. If you need a Washer repaired in the Houston area, our Washer repair technicians are always there for you! They always carry most common Washer parts that require replacement . All of the parts we provide are with a Full warranty from the manufacturer. For fast and reliable Same day Washer repair in the Houston area call today! Our service call is absolutely FREE with repair.
Basic Faults
Determine the cause of breakage of a washing machine – the key to success. After that, it only remains to replace the failed part. All faults can be divided into several types.
The washing machine does not turn on. Following the instructions in the manual, you need to check the voltage in the outlet, inspect the plug and the wire for damage, make sure that the plug is plugged into the wall outlet, and the power button is pressed.
Water does not get into the tank. The operating instructions suggest checking the correct connection to the water supply.
The water does not heat up to the set temperature: in this case it is necessary to make sure that the connection to the sewage system is correct.
The machine does not open – you may need to replace the broken handle. Jamming of the drum can become a foreign object that must be removed.
If leakage is detected, the junctions of the filler and drain hoses must be checked.
Do not drain the water – the cause may be a blockage of the drain valve.
Washer repair . No power supply
The reasons can be different. In addition to those mentioned above, the failure of the power button is not excluded. It does not close the circuit and the indication LEDs do not light. To get to it, you need to remove the top cover of the washing machine by unscrewing the screws and opening the latches. To test the button you need to have at your disposal a simple tester. With its help, we test the button in the pressed state. If the indication of the indicator or the sound signal does not inform you that the contact is closed, the button should be replaced.
Washer repair . Water does not enter the tank.
Most often the cause of the malfunction is clogging the inlet to the valve. A sign of this is the appearance of characteristic noise. All is adjusted after cleaning the filter net, for access to which it is required to unscrew the water inlet hose. Next, make sure that the voltage on the fence valve contacts is present.
Washer repair . The water entering the tank remains cold
You can check it by simply touching the sunroof glass. If it is cold, you should look for the cause, which can be a failure of the heater, its fouling with scum or the malfunction of the temperature sensor.
In some cases, the control unit or the complete absence of water in the tank may fail.
It should also check the presence of a breakdown on the body of the washing machine. In case of malfunction, the heater must be replaced.
Washer repair . The thermostat breaks down.
It can be attached to the surface of the heater or to be on the heater. In the first case, replace the part simply, in the other – you need to loosen the nuts fixing the heater, disconnect the wires and remove the thermostat from the seal.
Washer repair . The drum does not rotate
In this case, you need to inspect the drive belt: it can fall off the pulley, tear or stretch.
First you must turn off the machine and remove the plug from the outlet, then open the hatch. Scrolling the drum by hand, you need to listen: if the rotation of the rotor of the engine is not felt – dismantle the back cover. We change the belt or put it in its place. To purchase a belt of the same type, you need to read the marking, otherwise the length or size of the wedges will not match this model.
If the engine becomes unusable, it must be replaced.
To make sure the engine is malfunctioning, the tester needs to check its windings.
It is possible to repair the washing machine on its own in some cases, but it is worth it if there are certain skills and knowledge. Otherwise – it is better to contact the Washer repair .
This is simply necessary in case of a complex breakdown.