THERMADOR Error Code Fd – How to fix? by HoustonAuthorizedRepair.com

THERMADOR Range/Stove/Oven Fault Codes starting with an F – How to fix? by HoustonAuthorizedRepair.com 

THERMADOR Error Code Fd
Professional Ranges Models: PDR30/36/48…PRG30/36/48

ERROR CODEDESCRIPTION RESOLUTION
CODE Fd Bake & Broil relay drives active simultaneously. Check relay board for damage: trace E6 to K2 & K3, and burned contacts K3 & K4 Repair electronic range control (also called clock or ERC). Replace relay board if necessary

The control continuously monitors system parameters for control and oven failures and reports a fault code when a system problem is detected. The control utilizes the ovens blue “on light” and oven “heating light” to report a detected fault code. The control will continue to flash the lights in the appropriate sequence as long as the fault exists.

Detection of a fault does not hinder the ability of the control to continue to function if the fault is not critical for the intended operation. For example: If the range door latch is inoperative, the range will continue to cook since the fault would only prevent the range from self-cleaning.

HOW TO INTERPRET CODES

When a fault occurs, the control will flash the blue oven “on light” and the Blue “heating light” sequentially to indicate the fault. The fault codes have two numbers, these numbers are interpreted by the number of times the lights flash. The oven “on light” will flash indicating the first number, and the “heating light” will flash indicating the second number.

EXAMPLE:

Error E9 is…. No Cooling Fans. The code is 43. The oven “on light” will flash four times, then the “heating light” will flash three times, then pause. The sequence will then repeat as long as the fault is present.

ERROR CODES FOR OVENS WITH DREEFS CONTROL

The following chart shows the error codes that can be displayed in the Oven/Selector window during specific oven malfunctions. Some of the error messages can be cleared by performing the following steps:
1.Turn the selector knob to OFF
2.“Tweak” the oven by turning the selector knob slightly to the left (counterclockwise). This may stop the flashing message/beeping and clear the window.
3.For errors E1, E9, E11, E12 and E13, the power supply going to the even must be turned off momentarily, and back on again.
4.If an error remains displayed when the selector switch is OFF, and after attempting to clear the display, as shown in steps 2 and 3, turn off the power going to the oven, and refer to the chart below to help you find the problem.

ERROR CODE NOTE CHECK REPAIR
F0 Internal logic failure; cancel key supervision. Sounds alarm and resets to non-cook mode Replace the electronic range control (also called clock or ERC)
F1 Internal logic failure (monitoring function). Sounds alarm and inhibits cook modes Replace the electronic range control (also called clock or ERC)
F2 Temperature runaway detected (Bake/Broil: 600 – 700 F; Clean: 930 – 1000 degrees F). Sounds alarm and resets to non-cook mode. Check relay board for stuck contacts. Check oven temperature sensor for normal room temperature resistance (1085-1097 ohms at 75 degrees F). Check sensor wiring connectors for a loose or high resistance connection. Check electronic range control (also called clock or ERC) functions Replace relay board if necessary. Replace oven temperature sensor if other components check normal. If failure repeats, replace electronic range control (also called clock or ERC)
F3 Open circuit detected; oven temperature sensor. Check sensor for normal room temperature resistance (1085-1097 ohms at 75 degrees F). Check wires and connections between electronic range control (also called clock or ERC) and oven temperature sensor Replace sensor if other components check normal. Replace electronic range control (also called clock or ERC) if fail code reoccurs
F4 Short circuit detected; oven temperature sensor. Check sensor for normal room temperature resistance (1085-1097 ohms at 75 degrees F). Check wires between electronic range control (also called clock or ERC) and sensor. Replace sensor if other components check normal. Replace electronic range control (also called clock or ERC) if fail code reoccurs
F7 Function key shorted for over 16 seconds. Check for something pressing a key or preventing normal release of the key Replace electronic range control (also called clock or ERC) if other components check normal
F8 Internal logic failure; calibration. Alarm sounds and resets to non-cook mode. Check oven temperature sensor for normal room temperature resistance (1085-1097 ohms at 75 F). Check wires and connections between electronic range control (also called clock or ERC) and oven temperature sensor Replace electronic range control (also called clock or ERC) and oven temperature sensor if other components check normal
F9 Internal logic ailure; door latch supervision. Alarm sounds and resets to non-cook mode. If door is locked due to clean temperatures, disconnect power until door can be unlocked Replace the electronic range control (also called clock or ERC)
Fd Bake & Broil relay drives active simultaneously. Check relay board for damage: trace E6 to K2 & K3, and burned contacts K3 & K3 Replace electronic range control (also called clock or ERC). Replace relay board if necessary
Blank Display No power to lectronic range control (also called clock or ERC). Check oven light and cooktop dial lights (powered by L2 & L1, respectively). Check relay board transformer primary, E1 to E2 (140 ohms typical). If the transformer internal fuse is still OK, check output voltages, pins 9 – 8 (3.2 v.a.c.) and 7 – 6 (21 v.a.c.). Check clock functions after replacing relay board If relay board transformer open (E1 to E2), replace relay board. If still no clock functions replace electronic range control (also called clock or ERC)

ERROR CODENOTES
A Turns heat off on the failed oven only; microwave not affected.
B Turns all heat off; microwave not affected.
C Disables the CLEAN mode in both ovens; allows COOK and microwave.
D Error will remain in the display until oven is repaired and powered back up. No error tones.
E Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN.
F Tweaking clears to “—“ for retry.
G Clears when the oven temperature is less then the runaway temperature with the selector switch off.
H Can be cancelled by tweaking if a good sensor is detected.
I Cleared with a mode change.
J Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door.
K Turns heat and microwave off.
L If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message.
Sub Zero Repair Los Angeles Calendar

Flexible Scheduling

You can book, change or cancel your Appliance repair appointment at any time online
Sub Zero Repair Los Angeles Protect

Appointment Updates

We’ll update you about your Appliance repair appointment via text, email or phone
Sub Zero Repair Los Angeles Reviews

Protection Plans

Protect all your home’s appliances and systems.

Some About Services

Professional service you can trust!

When you need appliance repair service. We are available for your call 24 hours a day, 7 days a week, and we offer same day service. We service and repair all major brands.

Our service call is free with any repair that we perform and we always provide a written estimate before the repair, which must be by you in order for us to complete the service

Schedule Appointment

Our Advantages

Sub Zero Repair Los Angeles Time

Fast And Convenient Service

Same Day Appointment Guarantee! Small 3 hours appointment window, no late arrivals!

Sub Zero Repair Los Angeles Subject

Free Estimate

If You Choose to Do the Repair With Us! Always Detailed estimates in writing!

Sub Zero Repair Los Angeles Quality

Quality Repair

Experienced technicians: Licensed, Fully Insured and Well-Trained to work with High-End Appliances!

Sub Zero Repair Los Angeles Money

Flate - Rate Pricing

No Hourly Rates, No Extra Charges For Late Hours or Weekends!

92% clients recommend our repair service

Excellent service

Arrived on time and completed service He was very courteous and made sure I had the correct parts to fix my the sears vent.

January 9, 2017

Good service

Thanks to the company, called the operator called back 10 minutes later a technician Tom, for 2 hours the technician was with me, the vacuum cleaner repaired quickly and efficiently. I will recommend.

January 29, 2017

Well done

I broke the oven timer LG, without it it was impossible to turn on the oven. Came technician Jim, determined damage and eliminated all done quickly and well. A skilled technician, I recommend this company!

January 30, 2017